Metrologic MS5100 Betriebsanweisung Seite 1

MS5100 Eclipse Series User’s Guide

6 Cable Installation and Removal Installation 1. Insert the cable’s modular connector into the socket on the scanner. 2. Pull gently on the cable

7 Installation RS232, Light Pen or Laser Emulation 1. Turn off the host system. 2. Plug the male, 10-pin RJ45 end of the PowerLink cable into the

8 RS485 1. Turn off the host system. 2. Plug the male 10-pin RJ45 end of the MVC cable into the 10-pin socket on the MS5145. 3. Connect the othe

9 Keyboard Wedge 1. Turn off the host system. 2. Plug the male, 10-pin RJ45 end of the PowerLink cable into the 10-pin socket on the MS5145. 3.

10 Stand-Alone Keyboard 1. Turn off the host system. 2. Connect the 10-pin RJ45 male connector into the jack on the Eclipse. There will be a ‘c

11 Figure 9. USB USB: Low Speed USB (-38) Full Speed USB (-40) 1. Turn off the host system. 2. Connect the 10-pin RJ45 male connector of the US

12

13 Scanner Operation Modes of Operation CodeGate® CodeGate activates when removed from the stand , Out-of-Stand  Bar code data is transmitted w

14 Audible Indicators When the MS5145 scanner is operational, the scanner provides audible feedback to indicate the status of the scanner and the l

15 Visual Indicators The MS5145 is equipped with a red LED and green LED, which indicate the scanner’s state and the status of the current scan whe

Disclaimer Honeywell International Inc. (“HII”) reserves the right to make changes in specifications and other information contained in this documen

16 Failure Modes One Razzberry Tone – On Power Up This indicates the scanner has experienced a laser or flipper subsystem failure. Return the unit

17 Depth of Field by Bar Code Element Width Minimum Bar Code Element Width A B C D E F mm .10 .12 .17 .26 .33 .66 mils 4.1 4.8 6.8 10.4

18

19 Troubleshooting Guide The following guide is for reference purposes only. Contact a customer service representative (see page 43) to preserve t

20 Symptoms Possible Causes Solution The unit powers up, but does not scan and/or beep. The unit is trying to scan a particular symbology that is

21 Symptoms Possible Causes Solution The unit scans but the data is not correct. The unit’s configuration is not correct. Make sure that the pro

22

23 Design Specifications Operational Light Source: Visible Laser Diode (VLD) @ 650 nm Laser Power: Less than 1.0 mW average Embedded Laser: Max Pow

24 Electrical Input Voltage: 5VDC ± 0.25V Power: Operating: 675 mW Current: Operating: 135 mA average @ 5VDC DC Transformers: Class II; 5.2VDC

25 Applications and Protocols The model number on each scanner includes the scanner number and factory default communications protocol. Scanner Ve

iii Table of Contents Introduction ... 1Product Overvie

26

27 Configuration and Upgrades Configuration Modes The MS5145 Eclipse has three modes of configuration. • Bar Codes The Eclipse can be configured b

28 4. During configuration, the motor and laser turn off. YOU CANNOT SCAN A BAR CODE WHILE IN SERIAL CONFIGURATION MODE. 5. There is a 20 second

29 EXAMPLE #3: The following example shows the events that occur when an invalid bar code is sent. This sample will load the factory default sett

30 Upgrading the Firmware The MS5145 is part of Honeywell’s line of scanners with flash upgradeable firmware. The upgrade process requires a new fi

31 Scanner and Cable Terminations Scanner Pinout Connections The MS5145 scanner interfaces terminate to a 10-pin modular jack. The serial number la

32 Scanner Pinout Connections Figure 15. MS5145-00 Laser Emulation Pin Function 1 Ground 2 RS232 Transmit Output 3 RS232 Receive Input 4 Flip

33 Cable Connector Configurations RS232 PowerLink Cable, 55-55000x-3 Pin Function 9-Pin D-Type Connector 1 Shield Ground 2 RS232 Transmit Outp

34 Cable Connector Configuration Keyboard Wedge PowerLink Cable 55-55002A-3 Pin Function 5-Pin DIN, Female 1 Keyboard Clock 2 Keyboard Data 3

35 Limited Warranty Honeywell International Inc. ("HII") warrants its products and optional accessories to be free from defects in materi

iv Scanner and Cable Terminations Scanner Pinout Connections ... 31Cable Con

36 All provisions of this Limited Warranty are separate and severable, which means that if any provision is held invalid and unenforceable, such de

37 Regulatory Compliance Safety ITE Equipment IEC 60950-1 Second Edition EN 60950-1 Second Edition Laser Laser Class 1: IEC 60825-1: Second Editio

38 Achtung Die Verwendung anderer als der hier beschriebenen Steuerungen, Einstellungen oder Verfahren kann eine gefährliche Laserstrahlung hervorr

39 This equipment has been tested and found to comply with limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits

40 Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment

41 Index A AC ... see power accessories ... 2, 3 aperture ...

42 T terminations ... 31–34 tone ... 1, 14 transformer ... see power

43 Customer Support Technical Assistance If you need assistance installing or troubleshooting your device, please contact us by using one of the m

Honeywell Scanning & Mobility 9680 Old Bailes Road Fort Mill, SC 29707 www.honeywellaidc.com 70-79016 Rev G 12/12

1 Introduction Product Overview The MS5145 Eclipse is a single-line, hand-held laser scanner. Equipped with Honeywell’s patented CodeGate™ technol

2 Basic Kit Components Part # Description MS5145 Eclipse Scanner 00-02544 MetroSelect Single-Line Configuration Guide* 70-79016 MS5100 Eclipse

3 Part # Description 55-55000x-3 RS232 PowerLink Cable with Built-in Power Jack straight cord, long strain relief, black 55-55002x-3 Keyboard Wed

4 MS5145 Components Item No. Description 1 Mode Select Button/CodeGate Button (see page 13) 2 Red LED (see page 15) 3 Green LED (see page 15) 4

5 Caution and Serial Number Labels Figure 2. Label Location on the Bottom of the Scanner with Example Caution: To maintain compliance with appli